Generic XFP-10G32-BX60 Compatible 10G XFP BX-D Transceiver Module 60km
Built for hosts recognizing XFP-10G32-BX60, this HT-manufactured XFP module delivers 10G transmission at 1330nm-TX/1270nm-RX. Its rated reach is 60km, with LC simplex as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: XFP-10G32-BX60HT Part Number: XFP-10G32-BX60
Product Highlights
- Compatible alternative to Generic XFP-10G32-BX60
- 10G connectivity at 10Gbps
- Optical wavelength: 1330nm-TX/1270nm-RX
- Specified reach: 60km
- LC simplex / SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| HT Part Number | XFP-10G32-BX60 |
|---|---|
| Manufacturer | HT |
| Form Factor | XFP |
| Max. Data Rate | 10Gbps |
| Wavelength | 1330nm-TX/1270nm-RX |
| Max. Transmission Distance | 60km |
| Connector | LC simplex |
| Transmitter Type | DFB BiDi |
| Media | SMF |
| DOM Support | YES |
| TX Power | 1~5dBm |
| Receiver Sensitivity | < -20dBm |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Protocols | SFP+ MSA Compliant, CPRI, eCPRI |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 10Gbps, wavelength 1330nm-TX/1270nm-RX, rated reach 60km.
Applications and Optical Link Design
This BiDi interface is useful where only one fiber strand is available between two sites or racks. It must be paired with the complementary wavelength direction: one end transmits on the wavelength that the other end receives. Verify the paired part number, connector polish and fiber plant before installation, and measure link loss against the specified optical budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a XFP housing alone does not make two transceiver types interoperable.
This single-fiber interface must be paired with the complementary wavelength direction. One end transmits on the wavelength the other receives. Verify connector polish and measure loss over the 60km design range before service.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is 1~5dBm; receiver sensitivity is < -20dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Each XFP-10G32-BX60 compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Generic Compatibility and Factory Testing
Factory verification starts with the expected XFP-10G32-BX60 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use LC simplex with SMF. The specified maximum reach is 60km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Use XFP-10G32-BX60 as the compatibility cross-reference and XFP-10G32-BX60 as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
