Cisco DWDM-SFP10G-60.61 Compatible 10G SFP+ Transceiver Module 40km on OS2
This Cisco DWDM-SFP10G-60.61 compatible transceiver provides 10G connectivity in a hot-swappable SFP+ package. Its optical design operates at 1560.61nm for up to 40km on OS2, using Duplex LC/UPC. Complete parameters and related OEM references help field technicians install, maintain and identify the exact compatible module.
OEM Part Number: DWDM-SFP10G-60.61HT Part Number: DW-SFP10G40-21
Product Highlights
- Compatible alternative to Cisco DWDM-SFP10G-60.61
- 10G connectivity at 10Gbps
- Optical wavelength: 1560.61nm
- Specified reach: 40km on OS2
- Duplex LC/UPC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| Cisco Compatible | DWDM-SFP10G-60.61 |
|---|---|
| Manufacturer | HT |
| HT Part Number | DW-SFP10G40-21 |
| Form Factor | SFP+ |
| Max Data Rate | 10Gbps |
| Wavelength | 1560.61nm |
| Max Cable Distance | 40km@OS2 |
| Connector | Duplex LC/UPC |
| Media | SMF |
| Transmitter Type | EML DWDM |
| Receiver Type | PIN |
| TX Power | -1~4dBm |
| Receiver Sensitivity | <-15dBm |
| Power Budget | 14dB |
| Receiver Overload | 0dBm |
| Max. Power Consumption | 1.6W |
| Extinction Ratio | >6dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Bit Error Ratio (BER) | 1E-12 |
| Protocols | SFP+ MSA, CPRI, eCPRI, SFF-8472, SFF-8431 |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 10Gbps, wavelength 1560.61nm, rated reach 40km on OS2.
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
Wavelength-selective links require the exact channel plan at both ends. Confirm that filters pass 1560.61nm, then include their insertion loss in the 40km on OS2 power budget. A nearby channel is not a substitute for the specified wavelength.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -1~4dBm; receiver sensitivity is <-15dBm; the stated optical power budget is 14dB. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Cisco Compatibility and Factory Testing
The module is checked for host recognition as DWDM-SFP10G-60.61, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Cisco transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies DWDM-SFP10G-60.61, not an original Cisco-branded module.
Which fiber and connector are required?
Use Duplex LC/UPC with SMF. The specified maximum reach is 40km on OS2, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Use DWDM-SFP10G-60.61 as the compatibility cross-reference and DW-SFP10G40-21 as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
