Cisco DWDM-SFP10G-60.61-I Compatible 10G SFP+ Transceiver Module 40km on OS2
The DWDM-SFP10G-60.61-I compatible module serves equipment requiring a 10G SFP+ interface with 1560.61nm optics and a 40km on OS2 rating. Connection is through Duplex LC/UPC. Product data, application guidance and factory verification are presented together to support field technicians install, maintain and identify the exact compatible module.
OEM Part Number: DWDM-SFP10G-60.61-IHT Part Number: DW-SFP10G40-21-I
Product Highlights
- Compatible alternative to Cisco DWDM-SFP10G-60.61-I
- 10G connectivity at 10Gbps
- Optical wavelength: 1560.61nm
- Specified reach: 40km on OS2
- Duplex LC/UPC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: -40 to 85°C (-40 to 185°F)
Specifications
| Cisco Compatible | DWDM-SFP10G-60.61-I |
|---|---|
| Manufacturer | HT |
| HT Part Number | DW-SFP10G40-21-I |
| Form Factor | SFP+ |
| Max Data Rate | 10Gbps |
| Wavelength | 1560.61nm |
| Max. Data Rate | 11.3Gbps |
| Wavelength | 1563.86nm |
| Max. Cable Distance | 40km@OS2 |
| Connector | Duplex LC/UPC |
| Media | SMF |
| Transmitter Type | DWDM EML |
| Receiver Type | PIN |
| TX Power | -1~4dBm |
| Minimum Receiver Power | -15dBm |
| Power Budget | 14dB |
| Receiver Overload | 0dBm |
| Max. Power Consumption | 1.9W |
| Extinction Ratio | >6dB |
| DDM/DOM | Supported |
| Industrial Temperature Range | -40 to 85°C (-40 to 185°F) |
| Protocols | SFP+ MSA, SFF-8431, SFF 8472, 10GBASE-ER/EW, SDH STM64 |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 10Gbps, wavelength 1560.61nm, rated reach 40km on OS2.
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
The industrial temperature rating makes this version appropriate for controlled outdoor cabinets, transport nodes and other installations exposed to wider ambient temperature variation. Adequate airflow, protected cable routing and host-platform temperature limits still apply.
Wavelength-selective links require the exact channel plan at both ends. Confirm that filters pass 1560.61nm, then include their insertion loss in the 40km on OS2 power budget. A nearby channel is not a substitute for the specified wavelength.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -1~4dBm; the stated optical power budget is 14dB. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Each DWDM-SFP10G-60.61-I compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Cisco Compatibility and Factory Testing
Factory verification starts with the expected DWDM-SFP10G-60.61-I identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Cisco transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies DWDM-SFP10G-60.61-I, not an original Cisco-branded module.
Which fiber and connector are required?
Use Duplex LC/UPC with SMF. The specified maximum reach is 40km on OS2, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Use DWDM-SFP10G-60.61-I as the compatibility cross-reference and DW-SFP10G40-21-I as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
