Generic QDD-PLR4-400G Compatible 400G QSFP-DD PLR4 Transceiver Module
Built for hosts recognizing QDD-PLR4-400G, this HT-manufactured QSFP-DD module delivers 400G transmission at 1310nm. Its rated reach is 10km, with MPO-12/APC as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QDD-PLR4-400GHT Part Number: QDD-PLR4-400G
Product Highlights
- Compatible alternative to Generic QDD-PLR4-400G
- 400G connectivity at 425Gbps (4x 106.25Gbps)
- Optical wavelength: 1310nm
- Specified reach: 10km
- MPO-12/APC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QDD-PLR4-400G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP-DD |
| Max. Data Rate | 425Gbps (4x 106.25Gbps) |
| Wavelength | 1310nm |
| Max. Cable Distance | 10km |
| Connector | MPO-12/APC |
| Media | SMF |
| Transmitter Type | EML |
| Receiver Type | PIN |
| TX Power | -1.9~4.8dBm |
| Minimum Receiver Power | -8.2dBm |
| Power Budget | 6.3dB |
| Receiver Overload | 4.8dBm |
| Max. Power Consumption | 9W |
| Extinction Ratio | 3.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 8x50G-PAM4 |
| Modulation (Optical) | 4x100G-PAM4 |
| CDR (Clock and Data Recovery) | TX & RX Built-in DSP |
| Host FEC | Supported |
| Protocols | QSFP-DD MSA HW Rev 5.1, QSFP-DD, CMIS Rev 5.0, IEEE 802.3cu, IEEE 802.3bs |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 425Gbps (4x 106.25Gbps), wavelength 1310nm, rated reach 10km.
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 400G interface configuration must match the remote equipment; sharing a QSFP-DD housing alone does not make two transceiver types interoperable.
Before commissioning, measure the complete single-mode channel against the stated budget for 10km. Inspect every MPO-12/APC connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -1.9~4.8dBm; the stated optical power budget is 6.3dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Each QDD-PLR4-400G compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Generic Compatibility and Factory Testing
Compatibility testing for QDD-PLR4-400G combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use MPO-12/APC with SMF. The specified maximum reach is 10km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Quote HT part number QDD-PLR4-400G together with OEM reference QDD-PLR4-400G and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
