Cisco SFP-25G-LR-S Compatible 25G SFP28 LR Transceiver Module
The SFP-25G-LR-S compatible module serves equipment requiring a 25G SFP28 interface with 1310nm optics and a 10km rating. Connection is through Duplex LC. Product data, application guidance and factory verification are presented together to support field technicians install, maintain and identify the exact compatible module.
OEM Part Number: SFP-25G-LR-SHT Part Number: SFP-25GLR-31
Product Highlights
- Compatible alternative to Cisco SFP-25G-LR-S
- 25G connectivity at 25.78Gbps
- Optical wavelength: 1310nm
- Specified reach: 10km
- Duplex LC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| Cisco Compatible | SFP-25G-LR-S |
|---|---|
| Manufacturer | HT |
| HT Part Number | SFP-25GLR-31 |
| Form Factor | SFP28 |
| Max Data Rate | 25.78Gbps |
| Wavelength | 1310nm |
| Max Cable Distance | 10km |
| Connector | Duplex LC |
| Media | SMF |
| Transmitter Type | DFB 1310nm |
| Receiver Type | PIN |
| TX Power | -4~2dBm |
| Minimum Receiver Power | <-12dBm |
| Power Budget | 8dB |
| Receiver Overload | 2dBm |
| Power Consumption | <1.2W |
| Extinction Ratio | 3.5dB |
| CDR | TX and RX |
| Inbuilt FEC | Yes |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | MSA Compliant, CPRI, eCPRI |
| Core Size | G.652 |
| Packaging Technology | BOX Packaging |
| DDM/DOM | Supported |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 25.78Gbps, wavelength 1310nm, rated reach 10km.
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 25G interface configuration must match the remote equipment; sharing a SFP28 housing alone does not make two transceiver types interoperable.
Before commissioning, measure the complete single-mode channel against the stated budget for 10km. Inspect every Duplex LC connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -4~2dBm; the stated optical power budget is 8dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Cisco Compatibility and Factory Testing
Compatibility testing for SFP-25G-LR-S combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Cisco transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SFP-25G-LR-S, not an original Cisco-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 10km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Quote HT part number SFP-25GLR-31 together with OEM reference SFP-25G-LR-S and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
