NETGEAR AXM763 Compatible 10G SFP+ LRM Transceiver Module
Built for hosts recognizing AXM763, this HT-manufactured SFP+ module delivers 10G transmission at 1310nm. Its rated reach is 220m on OM3 / 300m on SMF, with Duplex LC as the physical interface. The specifications and engineering guidance below support field technicians install, maintain and identify the exact compatible module, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: AXM763HT Part Number: SFP-10GLRM-31
Product Highlights
- Compatible alternative to NETGEAR AXM763
- 10G connectivity at 10Gbps
- Optical wavelength: 1310nm
- Specified reach: 220m on OM3 / 300m on SMF
- Duplex LC / MMF/SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| NETGEAR Compatible | AXM763 |
|---|---|
| Manufacturer | HT |
| HT Part Number | SFP-10GLRM-31 |
| Form Factor | SFP+ |
| Max. Data Rate | 10Gbps |
| Wavelength | 1310nm |
| Max. Transmission Distance | 220m@OM3/300m@SMF |
| Connector | Duplex LC |
| Transmitter Type | FP 1310nm |
| Media | MMF/SMF |
| DOM Support | Yes |
| TX Power | -6.5~0.5dBm |
| Receiver Sensitivity | < -8.4dBm |
| Max. Power Consumption | ≤1W |
| Receiver Overload | +1.5dBm |
| Core Size | 50/125µm@OM3 MMF, 9/125μm@SMF |
| Modulation | NRZ |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Bit Error Ratio (BER) | 1E-12 |
| Protocols | IEEE 802.3ae, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA Compliant, CPRI, eCPRI |
Field Installation and Maintenance
Inspect the connector and patch lead before installation, then support the fiber without pulling on the module housing. Release the latch properly during maintenance and keep dust protection on unused interfaces. If a module is removed for later use, retain its part-number label and record its original port. For this model, the principal parameters are data rate 10Gbps, wavelength 1310nm, rated reach 220m on OM3 / 300m on SMF.
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The Duplex LC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
The multimode channel should use the fiber grade associated with the stated 220m on OM3 / 300m on SMF reach. Keep the Duplex LC end faces clean and avoid tight bends. Different multimode standards are not interchangeable merely because they share a connector.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -6.5~0.5dBm; receiver sensitivity is < -8.4dBm. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
NETGEAR Compatibility and Factory Testing
Factory verification starts with the expected AXM763 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original NETGEAR transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies AXM763, not an original NETGEAR-branded module.
Which fiber and connector are required?
Use Duplex LC with MMF/SMF. The specified maximum reach is 220m on OM3 / 300m on SMF, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Quote HT part number SFP-10GLRM-31 together with OEM reference AXM763 and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
